Reference

Automatic Gate Glossary

97 gate, operator, safety, and access control terms, each defined in plain language and linked to the guide that goes deeper. Search a word, or filter by topic.

Interactive

Anatomy of an automatic slide gate

Tap or hover a numbered point to see what the part is called and what it does. The same names show up in quotes, manuals, and inspection notes.

123456789101112
01

Operator

Read the guide

Side by side

Gate terms people mix up

Tap a card to see the difference in one breath.

Ready to plan a new gate?

Design, fabrication, installation, and service from one team in Sedro-Woolley.

A9 terms

Access control

Access control

The part of a gate system that decides who may open it and when. It can be as simple as a keypad code or as layered as cards, phone credentials, intercom calls, and license plate recognition, all logged and scheduled from one controller.

Read the guide

Access controller

Access control

The board or panel that stores users, codes, schedules, and event logs, and tells the gate operator to open. On larger sites it can manage several gates and doors from one system, locally or through a cloud portal.

Read the guide

Actuator

Operators

The motorized arm that pushes and pulls a swing gate leaf. Linear actuators extend and retract like a ram; articulated arms fold at an elbow. The choice depends on pillar depth, leaf weight, and how far the gate must swing.

Read the guide

ADA push-button actuator

Safety and standards

A large push plate, mounted on a wall or a bollard, that triggers an automatic door operator so a person can open the door without pulling or pushing it. Placement, height, and reach range are planned with the door's swing and the approach path.

Read the guide

Aluminum gate

Construction and materials

A gate built from aluminum sections. It is light, which eases the load on hinges and operators, and it does not rust, which matters near salt air. It is less stiff than steel, so long or tall leaves need careful framing and bracing.

Read the guide

Anti-tailgating

Access control

Logic or detection that keeps a second vehicle from slipping through behind an authorized one. Typical methods are a closing loop that closes the gate as soon as one vehicle clears, a short open time, and cameras that record each entry.

Read the guide

Articulated arm operator

Operators

A swing gate operator with a two-piece folding arm, similar to an elbow. It suits wide pillars and hinges set back from the face of the post, where a straight linear actuator would not have room to work.

Read the guide

ASTM F2200

Safety and standards

The Standard Specification for Automated Vehicular Gate Construction. It covers the gate itself: screening of openings, gaps at posts, guarded rollers, positive stops, protrusions, and separate pedestrian access. It works alongside UL 325, which covers the operator.

Read the guide

Automatic gate

Gate types

A gate that opens and closes under the control of an operator and its logic, triggered by a remote, keypad, loop, or schedule, without anyone pushing it. Every automatic gate is electric, but the word stresses the control system rather than the motor.

Read the guide

B4 terms

Barrier arm

Gate types

A single horizontal arm that lifts to let a vehicle pass, common at parking lots, garages, and toll style lanes. It controls traffic flow quickly but does not stop a person on foot, so it is often paired with a fence or a slide gate for security.

Read the guide

Battery backup

Power and wiring

Batteries, usually on a DC operator, that keep the gate cycling for a while after a power outage. How many cycles they deliver depends on battery size, gate weight, temperature, and age, so the system should be sized for the site rather than assumed.

Read the guide

Bifold gate

Gate types

A gate whose panels fold as they open, so it needs less clearance than a full swing leaf. The folds add pinch points, and UL 325 requires two independent entrapment protection means in both directions of travel for a horizontal bifold gate.

Bollard

Construction and materials

A short, sturdy post that keeps vehicles away from storefronts, entrances, pedestrian areas, and equipment. Bollards can be fixed, removable, retractable, decorative, or crash rated, and the right type depends on what the site needs to stop.

Read the guide

C11 terms

Cantilever gate

Gate types

A slide gate that rides on rollers mounted on posts beside the opening, with a counterbalance tail that extends behind it, so nothing touches the ground across the driveway. It works well where a ground track would fill with snow, ice, or gravel.

Read the guide

Card reader

Access control

A reader that opens the gate when a card or fob is presented. Most use RFID proximity or smart card technology. Each credential can be added, scheduled, or revoked individually, which is why card systems suit businesses and multi-family properties.

Read the guide

Cedar gate

Construction and materials

A gate built from cedar boards, often Western Red Cedar, usually on a steel frame when it will be automated. Cedar is light and naturally rot resistant; the frame keeps long wood leaves square under the load of an operator.

Read the guide

Cellular gate opener

Access control

A module that lets a gate be opened by phone call or app over the cell network, with no internet line at the gate. It needs adequate signal at the operator location, which in rural Northwest Washington should be tested before installation.

Read the guide

Chain drive

Operators

A slide gate drive where the operator pulls a roller chain anchored at each end of the gate. It is simple and forgiving of minor misalignment, but the chain needs tension and lubrication, and its exposed run should be guarded.

Read the guide

Class I, II, III, IV

Safety and standards

The UL 325 usage classes for gate operators. Class I is residential up to four homes, Class II commercial or public, Class III industrial not open to the public, and Class IV guarded restricted access. The operator must be listed for the class of the site.

Read the guide

Closing loop

Access control

A vehicle loop placed past the gate on the exit side. When a vehicle crosses and clears it, the operator closes the gate right away instead of waiting for a timer, which shortens the window for tailgating.

Read the guide

Constant pressure control

Safety and standards

Also called Type D entrapment protection. The gate moves only while someone holds the control, from a spot with a full view of the gate. UL 325 forbids automatic closing on this setup and allows no other activation device to be connected.

Control board

Operators

The circuit board inside the operator that runs the gate's logic: limits, speed, reversing, timers, inputs from remotes and loops, and monitoring of external safety sensors. Its settings decide how the gate actually behaves day to day.

Read the guide

Crash-rated bollard

Construction and materials

A bollard tested to stop a vehicle of a specified weight at a specified speed. Ratings come from standardized crash tests such as ASTM F2656, and the foundation is part of the rated system, so the installation must follow the tested design.

Read the guide

D3 terms

DC operator

Power and wiring

An operator with a low-voltage DC motor, typically 24 volts. DC drives allow soft starts and stops, variable speed, and battery backup, and they are common on residential and light commercial gates.

Read the guide

Double swing gate

Gate types

Two leaves hinged on opposite posts that meet in the middle. Each leaf is shorter than a single gate of the same width, which eases hinge loads and wind loads, but it needs two operators or a dual-leaf operator and a clean meeting point.

Read the guide

Drop rod

Construction and materials

A vertical pin that drops into the ground or a sleeve to hold a manual gate leaf in place. On an automated gate it is usually removed, because the operator or a lock now holds the leaf, and a dropped rod can fight the motor.

Need a term explained on your own gate?

We walk the gate with you, name every part, and tell you what is working and what is not.

E5 terms

Electric gate

Gate types

A gate moved by an electric motor rather than by hand. The term covers anything from a basic opener on a remote to a fully automated system with sensors, timers, and access control.

Read the guide

Electric gate lock

Access control

A lock powered by the gate system, such as a magnetic lock or a solenoid lock, that holds the gate closed against being pushed or forced. It is released by the operator before the gate moves, and its fail behavior must suit the site.

Read the guide

Emergency vehicle access

Safety and standards

The means fire, police, and EMS use to open a gate, such as a key switch or Knox box, a siren or strobe-activated sensor, or a manual release. Local fire marshals set what is required on fire apparatus access roads.

Read the guide

Entrapment zone

Safety and standards

Any place where a moving gate could catch or hold a person, such as the closing edge, the gap at the receiving post, or the space between an opening gate and a wall. UL 325 requires protection for each zone in each direction of travel.

Read the guide

Exit wand

Access control

A buried or surface-mounted vehicle sensor, often a magnetometer probe, that opens the gate as a car approaches from the inside. It is an alternative to a cut-in exit loop where the pavement cannot be saw cut.

Read the guide

F5 terms

Fail-safe and fail-secure

Access control

What a lock or gate does when power is lost. Fail-safe releases or opens; fail-secure stays locked. The choice depends on security needs and on egress and fire access rules, which can require a gate to be openable during an outage.

Read the guide

Farm gate

Gate types

A gate built for equipment, livestock, and rural driveways, usually wide and simple. When automated, its width, the turning room of trucks and implements, and the ground it swings or slides over drive the design.

Read the guide

Footing

Construction and materials

The concrete foundation that holds a gate post or operator pad. Its depth and width depend on gate weight, leverage, wind, and soil; an undersized footing is the most common reason a heavy swing gate starts to sag.

Read the guide

Free exit

Access control

A setup where vehicles leaving a property open the gate automatically, through an exit loop or wand, without a code or credential. It is convenient and common, but it should be planned with the site's security needs in mind.

Read the guide

Frost depth

Construction and materials

How deep the ground freezes in winter. Footings set below it are not lifted by frost heave. In Washington the required depth varies by jurisdiction and elevation, so it is checked locally before posts are poured.

Read the guide

G4 terms

Galvanizing

Construction and materials

A zinc coating, often applied by hot-dip galvanizing, that protects steel from rust. In wet and coastal climates it is often combined with powder coating, so the zinc protects the steel and the paint protects the zinc.

Read the guide

Gate operator

Operators

The motor and control unit that moves a gate, also called a gate opener. Operators are built for a gate type, a weight and length range, and a usage class, and should be matched to the gate rather than to a price point.

Read the guide

Gooseneck pedestal

Access control

A curved post that holds a keypad, card reader, or intercom at driver's window height on the approach to a gate. Its position sets how close a driver must pull up and must keep controls at least 6 feet from the gate.

Read the guide

Guide rollers

Construction and materials

Rollers mounted on a post that keep a slide gate upright and in line as it travels. They are not the weight-bearing wheels, but ASTM F2200 still requires exposed rollers within reach to be guarded.

H3 terms

Hinge

Construction and materials

The pivot that carries a swing gate leaf. Automated swing gates need heavy-duty, often ball-bearing hinges sized for the leaf weight, because worn or undersized hinges let a gate drop, bind, and overload the operator.

Read the guide

HOA gate system

Access control

A gate and access control system serving a homeowners association or shared community. It usually combines resident credentials, visitor entry through an intercom or codes, delivery access, and an administrator who manages users.

Read the guide

Hold-open mode

Operators

A setting or switch that keeps the gate open, for events, moves, or deliveries, without disabling its safety devices. A schedule can open and hold a gate for business hours and close it after.

Planning access control for a property?

Keypads, cards, intercoms, plates or phones: we match the system to who uses the gate.

I2 terms

Inherent entrapment protection

Safety and standards

Type A protection built into the operator. It senses that the gate has met resistance and reverses. It reacts only after contact, so UL 325 requires a second, independent means of a different type, usually an external sensor.

Read the guide

Intercom

Access control

An audio or video station at the gate that lets a visitor call the property, and lets the resident or staff open the gate remotely. Modern systems ring a phone or app instead of a fixed handset in the house.

Read the guide

K3 terms

Key switch

Safety and standards

A switch operated by a key, often used to give fire or police a way to open a gate, or to let staff override the system. Some jurisdictions specify a particular key system for fire department access.

Read the guide

Keypad

Access control

A code entry pad at the gate. It is the simplest credential to share and the hardest to control, because codes travel. Individual codes per user, scheduled codes, and logs reduce that weakness.

Read the guide

Knox box

Safety and standards

A locked box or key switch, accessible only to the fire department, that gives firefighters a key or a way to operate a gate in an emergency. Whether one is required depends on the local fire code official.

Read the guide

L6 terms

Leaf delay

Operators

A setting on a double swing gate that starts one leaf slightly before the other, so the leaves meet in the right order where one overlaps the other, and do not collide at the center.

License plate recognition

Access control

Cameras and software that read plates and open the gate for registered vehicles. Often called LPR, it is hands-free for residents and creates a record of entries, but it needs good camera placement and lighting to read reliably.

Read the guide

Limit

Operators

The setting or switch that tells the operator where the fully open and fully closed positions are. Limits that drift let a gate stop short or push into its stops, which wears hardware and can confuse safety logic.

Linear actuator

Operators

A straight ram-style swing gate operator that extends and retracts to move the leaf. It is compact and common on residential gates, and it needs enough post depth behind the hinge line to reach its full stroke.

Read the guide

Loop detector

Access control

A wire loop cut into the pavement and connected to a detector that senses the metal of a vehicle above it. Loops open the gate for exiting traffic, hold it open while a vehicle is in the path, and close it after a car clears.

Read the guide

Low-voltage wiring

Power and wiring

The control wiring between the operator and its keypads, loops, sensors, and intercom. It runs separately from line voltage and is buried in conduit at depths and with methods set by code and the inspector.

Read the guide

M4 terms

Magnetic lock

Access control

An electric lock, often called a maglock, that holds a gate closed with an electromagnet and a steel plate. It has no moving latch, which suits gates, but it releases when power is cut unless the system is designed otherwise.

Read the guide

Manual release

Operators

A key, lever, or knob that disengages the operator so the gate can be moved by hand during an outage or service. Owners should know where it is and how to re-engage it before the first winter storm.

Read the guide

Mesh screening

Construction and materials

Welded wire or perforated panel added to the lower part of a gate so a hand or a 2.25 inch sphere cannot pass through. ASTM F2200 requires it on slide gates up to 72 inches above grade, or the full height of a shorter gate.

Read the guide

Monitored sensor

Safety and standards

An external entrapment protection device the operator checks every cycle. If it is missing, disconnected, or faulty, the operator falls back to constant pressure operation. UL 325 requires monitoring of all external entrapment protection means.

Read the guide

Have a gate that does not match these definitions?

Older gates often predate today’s standards. We evaluate gates we did not install.

O1 term

Obstruction

Safety and standards

Anything in the gate's path when it moves. A listed operator must begin reversing within 2 seconds of sensing one and travel at least 2 inches back; a second sequential obstruction sensed by inherent protection stops the gate and sounds an alarm.

Read the guide

P8 terms

Pedestal

Access control

A post that holds a keypad, reader, intercom, or camera at the right height and distance from the gate. Its location affects how easily drivers reach it, how well cameras see, and whether controls stay out of reach of the moving gate.

Read the guide

Pedestrian gate

Gate types

A gate sized for people, kept separate from the vehicle gate. Vehicular gate operators may not be used on pedestrian gates, and separate pedestrian access is required where people are likely to walk in or out.

Read the guide

Photo eye

Safety and standards

A photoelectric sensor that sends a beam across the gate's path and signals the operator when something breaks it. It is Type B1, non-contact entrapment protection, and it must be a model the operator lists as compatible so it can be monitored.

Read the guide

Positive stop

Construction and materials

A fixed stop that limits a slide gate to its designed open and closed positions so it cannot run off its rollers or track. ASTM F2200 requires them at the top or bottom of the gate.

Read the guide

Post

Construction and materials

The vertical member that carries a gate's hinges, rollers, receiver, or operator. Its size, wall thickness, and footing have to match the gate's weight and leverage, which grow quickly with leaf length.

Read the guide

Powder coating

Construction and materials

A dry paint that is applied electrostatically and baked into a hard, even finish. On steel gates it is usually applied over galvanizing for wet and coastal climates, and its color and gloss are chosen with the property.

Read the guide

Privacy gate

Gate types

A solid or near-solid gate that blocks the view into a property. Solid faces catch more wind, so privacy gates need stronger posts, hinges, and operators than open picket gates of the same size.

Read the guide

Proximity credential

Access control

A card, fob, or sticker that a reader detects at short range without contact, using RFID. Each one can be issued and revoked individually, unlike a shared code.

Read the guide

R6 terms

Rack and pinion

Operators

A slide gate drive where a gear on the operator engages a toothed rack mounted along the gate. It is quieter and cleaner than a chain, and the rack must stay aligned with the gear along the full travel.

Read the guide

Receiver guide

Construction and materials

The bracket that catches the leading edge of a slide gate in the closed position and keeps it from being pushed sideways. ASTM F2200 sets where it may sit so it is not a puncture hazard.

Read the guide

Remote transmitter

Access control

A handheld or visor remote that opens the gate by radio. Rolling code remotes change their signal each press so it cannot simply be recorded and replayed.

Read the guide

Retractable bollard

Construction and materials

A bollard that lowers into the ground to let authorized vehicles pass, then rises again. It can be manual, hydraulic, or electric, and powered models are often tied into access control.

Read the guide

RFID

Access control

Radio frequency identification, the technology behind most cards, fobs, and long-range vehicle tags used at gates. Readers identify each credential, so access can be logged per person or per vehicle.

Read the guide

Rollers

Construction and materials

The wheels that carry a slide gate, either on a ground track or on cantilever carriages. Weight-bearing rollers within 8 feet of the ground must be guarded or covered under ASTM F2200.

Read the guide

S8 terms

Safety edge

Safety and standards

A contact sensor, Type B2, mounted on a gate's leading or trailing edge. It signals the operator the instant it is pressed. It must sit where an object would actually be caught and be a model compatible with the operator.

Read the guide

Safety loop

Safety and standards

A vehicle loop in the gate's path that keeps the gate from closing or moving while a vehicle sits on it. Under a swing path it is often called a shadow loop. It protects vehicles, not people, so it does not replace UL 325 entrapment protection.

Read the guide

Slide gate

Gate types

A gate that moves sideways along the fence line, on a ground track or cantilever rollers. It needs room beside the opening for the gate to slide into, but no room in front or behind, which suits slopes and short driveways.

Read the guide

Soft start and stop

Operators

Operator settings that ramp the motor up and down at the start and end of travel. They reduce shock on hinges, rollers, and the gate frame, and make the gate quieter.

Solar gate opener

Power and wiring

An operator powered by a battery that a solar panel recharges, used where running power is impractical. It works only when panel size, battery capacity, and daily cycles are sized for winter light, not summer light.

Read the guide

Strobe sensor

Safety and standards

A receiver that opens a gate when it detects the strobe signal emitted by equipped emergency vehicles. Whether a site needs one, and which system, is set by the local fire department.

Read the guide

Surge protection

Power and wiring

Devices that protect the operator's electronics from voltage spikes on the power line and on long control, loop, or phone wires. Control boards are the most expensive part to replace after a spike.

Swing gate

Gate types

A gate that pivots on hinges, as a single leaf or a pair. It needs clear room to swing, which matters on slopes and near walls, and it catches more wind than a slide gate of the same face area.

Read the guide

T5 terms

Telephone entry

Access control

An entry system that calls a resident's phone from the gate so the visitor can be let in from anywhere. It is common at multi-family properties and HOAs, often with a directory on the panel.

Read the guide

Timer-to-close

Operators

A setting that closes the gate automatically after a set delay. Under UL 325 it is disabled after any stop or reversal by inherent or contact sensing, until the gate is reset, so it cannot close again on someone it just touched.

Read the guide

Track

Construction and materials

The rail a slide gate rolls on, often an inverted angle or V-track set in concrete. It must stay clean and level; gravel, ice, and packed snow in the track are a common cause of slide gate faults in winter.

Read the guide

Two-means rule

Safety and standards

The UL 325 requirement for at least two independent entrapment protection means for each entrapment zone. The same type of device cannot count for both, so two photo eyes in one zone are still one type.

Read the guide

Type B1 and B2

Safety and standards

The UL 325 letters for external entrapment protection. B1 is non-contact sensing, such as a photo eye. B2 is contact sensing, such as an edge. Both must be monitored by the operator.

Read the guide

U2 terms

UL 325

Safety and standards

The safety standard gate operators are tested and listed to. For gates it sets entrapment protection, monitoring, reversal behavior, speed and force limits, usage classes, and installation instructions.

Read the guide

Underground operator

Operators

A swing gate operator buried in a box beneath the hinge, so nothing shows above ground. It suits formal entrances, and it needs drainage, because a box that floods in a Northwest winter will fail.

Read the guide

V3 terms

Vertical lift gate

Gate types

A gate that rises straight up, used where there is no room to swing or slide. Its dangerous direction is down, which is why UL 325 asks for two entrapment protection means while closing and one while opening.

Vertical pivot gate

Gate types

A gate arm or panel that pivots upward through an arc, from horizontal to vertical. It moves quickly and needs little side room, and both directions of travel need two entrapment protection means.

Read the guide

Video intercom

Access control

An intercom with a camera, so the resident sees who is at the gate before opening it, often from a phone. Camera height, angle, and lighting decide whether faces and vehicles are actually visible at night.

Read the guide

W5 terms

Warning sign

Safety and standards

The placard that warns of a moving gate. UL 325 requires at least two, displayed in the area of the gate and visible from both sides of the opening, in the format the operator manufacturer supplies.

Read the guide

Wheel kit

Construction and materials

A wheel added to the free end of a long swing gate to carry part of its weight. It helps a sagging leaf, but it needs a smooth surface across the whole swing, and on gravel, slopes, or snow it can drag.

Read the guide

Wi-Fi gate control

Access control

A module that connects the operator or access controller to the property's Wi-Fi so the gate can be opened and monitored from an app. It depends on a reliable signal at the gate and on what happens when the internet is down.

Read the guide

Wind load

Construction and materials

The force wind puts on a gate's face. Solid and tall gates catch more of it, which affects post size, footing depth, hinge choice, and whether an operator can hold the gate closed in a storm.

Read the guide

Wrought iron gate

Construction and materials

A decorative gate in the traditional iron style, today usually made from steel with forged details. Its open pickets and scrolls often need lower screening before automation to meet ASTM F2200.

Read the guide

Missing a term?

Ask the people who build and service gates

Emerald Gate Systems designs, fabricates, installs, automates, and services gates as one team from our shop in Sedro-Woolley, across Skagit, Whatcom, and Snohomish counties and the islands. If a word in a quote or a manual is not here, call and ask.

Washington construction contractor registration EMERAGS748D6 and electrical contractor license EMERAGS747KE (Doors and Gates specialty).