Iron gates last a long time in Washington, but not without help. A gate that has stood through twenty wet winters in Mount Vernon, a few seasons of salt spray in Anacortes or years of sprinkler overspray in a Bellingham yard usually shows the same problems: rust at the bottom rail, a cracked weld at a picket, a hinge that has worn oval, paint that lifts in sheets. Wrought iron gate repair in Washington is mostly about catching those problems while the metal is still sound and fixing the cause, not just the stain.
This guide explains how to tell what your gate is made of, how rust and broken welds are repaired, what Washington’s lead paint rules mean for old painted gates, how repairs change when the gate has an automatic opener, and how to decide between repair and replacement. It is written for homeowners, property managers and HOAs in Skagit, Whatcom, Snohomish, Island, San Juan, King and Pierce counties.
Quick answer
Most wrought iron gate repair in Washington is rust removal, weld repair and hinge work. Clean rust back to sound metal, prime the same day and repaint. Cracked welds and loose pickets are cut out and rewelded. Pre-1978 painted gates fall under Washington’s lead renovation rules, and automated gates need a safety check after repairs.
In this guide
- What wrought iron gate repair in Washington usually involves
- Wrought iron, steel or cast iron: know what you are repairing
- Why iron gates rust in Western Washington
- How to inspect an iron gate before any repair
- Repairing rust on a wrought iron gate
- Old paint and Washington’s lead renovation rules
- Broken welds, loose pickets and missing ornaments
- Hinges, latches and sag on iron gates
- Galvanized and powder coated iron gates
- Repairing an automated iron gate
- Safety upgrades when an old iron gate is automated
- Repair or replace an iron gate?
- What owners can do and what needs a shop
- Keeping a repaired iron gate sound in Washington weather
- How we approach iron gate repair
- Frequently asked questions
What Wrought Iron Gate Repair in Washington Usually Involves
Orange streaks, a dragging leaf or a rattling picket are symptoms. In our part of the state the cause is almost always water held against metal for months. Wrought iron gate repair in Washington usually falls into a few groups of work:
- Rust and coating repair: removing rust and failed paint, treating pitted areas, priming and repainting.
- Structural repair: cracked or broken welds, rusted-through rails, loose or bent pickets, a frame that has racked out of square.
- Hardware repair: worn hinges and hinge pins, latches and drop rods, gate stops, lock boxes.
- Post and footing repair: a hinge post that leans, rusts at grade or has cracked its concrete.
- Automation repair: operator brackets, safety devices and the gate’s movement once an opener is attached.
Most gates need more than one of these at the same time. A sagging gate, for example, may have a worn hinge, a cracked weld at the hinge stile and rust where the bottom rail drags through wet gravel. Fixing only the hinge leaves the other two to fail again. If the main complaint is a gate that has dropped at the latch side, our guide to sagging gate repair in Washington goes through that problem step by step.
Wrought Iron, Steel or Cast Iron: Know What You Are Repairing
“Wrought iron” is used loosely. People call almost any dark ornamental metal gate a wrought iron gate, and the name says more about the style than the material. Before any repair, it helps to know which metal you are dealing with, because the repair methods are not the same.
- Steel bar and tube: many ornamental gates are built from solid steel bar for the pickets and steel tube or channel for the rails and stiles, welded together and painted or powder coated. Steel welds readily, which makes structural repair straightforward when the metal around the damage is still sound.
- Hand-forged iron work: scrolls, collars, leaves and twisted bars shaped hot at the forge. These can be repaired, but a missing piece usually has to be forged to match rather than bought.
- Cast ornaments: finials, rosettes, castings at the top of pickets or decorative panels. Cast iron is brittle, cracks rather than bends on impact, and is harder to weld than steel. A cracked casting is often replaced with a new piece rather than welded.
- Galvanized steel: a zinc coating applied by dipping the finished steel in molten zinc, often painted or powder coated on top. Welding through it and repairing the coating need extra steps, covered below.
A magnet sticks to all of these, so look at broken edges, joints and the gate’s history instead. Our page on iron gate installation explains the difference between ornamental iron and wrought iron work in more detail.
The material also matters for matching: a picket in the wrong bar size or a scroll with a different curve stands out on a uniform gate.
Why Iron Gates Rust in Western Washington
Steel and iron rust when bare metal is exposed to water and oxygen. Paint and other coatings slow that down by keeping water off the metal. The trouble starts when the coating is broken and water reaches the metal underneath, and in Western Washington water is rarely in short supply. Long wet seasons mean surfaces stay damp for weeks. Shaded gates under firs and cedars may never fully dry between October and spring.
Rust on iron gates tends to start in the same places:
- The bottom rail. It sits closest to wet ground, collects splash from rain and sprinklers, and holds leaves, needles and mud against the metal.
- Joints where pickets pass through rails. A punched rail with pickets through it creates small crevices that hold water. Paint cracks there first because the joint moves slightly with temperature.
- Hollow tube. Square or round tube can trap water inside if it has no drain hole. The tube rusts from the inside out and the outside may look fine until it splits or swells.
- Hardware contact points. Where a hinge, latch or bracket touches the gate, the coating gets scraped every time the gate moves. Steel bolts in aluminum or stainless hardware against carbon steel can also set up galvanic corrosion, where two different metals in contact with water corrode faster than either would alone.
- Post bases. The point where a steel post enters concrete or soil stays wet and often rusts below the surface where nobody looks.
Salt air on Fidalgo Island or Whidbey Island speeds corrosion further. Our guides to gate materials for Washington weather and the best gate materials for coastal Anacortes properties cover how the site changes the choice of metal and coating. For repair, the lesson is simple: find where water reaches the metal and change it.
How to Inspect an Iron Gate Before Any Repair
A careful look before any work starts saves money, because it separates cosmetic problems from structural ones. You can do most of this inspection yourself with a flashlight, a screwdriver or small pick, and a phone camera.
- Look at the whole gate from a distance. Is it level? Does the latch side hang lower than the hinge side? Is the frame still square, or has it twisted? Take a photo straight on so you can compare later.
- Open and close it by hand. Note any grinding at the hinges, any point where it drags, and whether the latch catches without lifting the gate. On an automated gate, release the operator first following its manual.
- Check the bottom rail closely. Push a screwdriver gently against rust spots. Hard metal under the rust is surface corrosion. If the tip sinks in, flakes come off in layers, or you can see daylight, the metal is thinning or rusted through.
- Check every weld you can reach. Look for hairline cracks, especially where pickets meet rails and where the hinge stile joins the rails. A rust line that follows a weld often means a crack underneath.
- Grab each picket and ornament. Anything that moves, rattles or rings differently from its neighbors has a broken joint.
- Look at the hinges and posts. Wiggle the gate up and down at the latch side. Movement at the hinge means worn pins or knuckles. Movement at the base of the post means a footing or post problem.
- Look inside tube ends and under caps. Swollen tube, split seams or rust weeping from a cap point to water trapped inside.
- Note the paint. Many layers of old paint on an older home’s gate raise the lead question covered below.
Photos of what you find help any shop scope the work. If the gate has an automatic opener, also see our page on gate repair in Northwest Washington for the operator side of the inspection.
Not sure if the rust on your iron gate is cosmetic or structural?
We inspect the frame, welds, hinges, posts and finish on a free on-site visit and tell you plainly what can be repaired in place, what should come to our Sedro-Woolley shop and what is past saving.
Repairing Rust on a Wrought Iron Gate
Rust repair comes down to three things: clean to sound metal, deal with lost metal, and recoat before the clean steel rusts again. Skipping steps is why so many repainted gates are orange again in two winters.

Step 1: Clean to sound metal
The coatings industry describes surface preparation levels in standards published by SSPC (now part of AMPP, the Association for Materials Protection and Performance). Three of them matter for gate work:
| Standard | Method | What it leaves | Where it fits on a gate |
|---|---|---|---|
| SSPC-SP 2 | Hand tool cleaning: wire brushes, scrapers, chisels, sanding blocks | Removes loose rust and paint only; tightly bonded material stays | Small touch-ups on a gate with mostly sound paint |
| SSPC-SP 3 | Power tool cleaning: powered wire brushes, grinders, sanders | Removes loose rust, mill scale and paint; adherent material may remain | Spot repair of rusted areas in place or in the shop |
| SSPC-SP 6 | Commercial blast cleaning with abrasive media | Removes nearly all rust, mill scale and paint, leaving at most light staining on part of the surface | Full restoration of a gate taken to a shop, before a new full coating system |
On a gate that will stay in place, hand and power tool cleaning are the usual choice. A gate that is being fully restored is often taken off its hinges and brought to a shop, where it can be blasted and coated under cover instead of in the rain. Blasting reaches inside scrolls and between pickets far better than a brush can. On an older painted gate, read the lead section below before any grinding or blasting starts.
Step 2: Deal with lost metal
Once the rust is off, look again. Shallow pitting can be primed and coated. Deep pits, thin spots and holes cannot be fixed with paint. Fillers and metal epoxies can smooth small cosmetic pits, but they add no strength, and on a bottom rail or hinge stile they hide a weak section rather than repair it. Structural members with real metal loss are repaired by cutting out the damaged section and welding in new steel of the same size, or by replacing the whole rail or picket.
When a section of hollow tube is replaced, a drain hole at the low point lets water out instead of letting it sit inside.
Step 3: Prime fast and coat completely
Freshly cleaned steel starts to flash rust quickly in damp air, sometimes within hours on a wet Washington day. The primer should go on the same day the metal is cleaned, on a dry surface, within the temperature and humidity range the coating maker lists on the product data sheet. A rust-inhibiting primer followed by finish coats made for exterior metal is the usual system. Pay extra attention to edges, welds, the undersides of rails and the inside of joints, where coatings are thinnest and rust starts first.
Painting outdoors on cold, wet days risks poor adhesion, which is one reason gates that need full refinishing often go to the shop.
Old Paint and Washington’s Lead Renovation Rules
Iron gates and fences at older homes often carry many layers of paint, and paint used before 1978 may contain lead. Washington runs its own lead-based paint renovation program through the Department of Commerce under chapter 365-230 WAC, and it reaches gate work more directly than many owners expect.
Three parts of the rule matter for an iron gate:
- Fences count. The rule’s definition of building components lists exterior components such as fences, railings, handrails and balustrades, alongside doors, siding and windows (WAC 365-230-020). A painted iron gate and fence at a covered property fall into that list.
- Which properties. The rules apply to target housing, which WAC 365-230-020 defines as housing built before 1978, with limited exceptions, and to child-occupied facilities such as day care centers and preschools in pre-1978 buildings.
- Size threshold. Under WAC 365-230-310, minor repair and maintenance that disturbs twenty square feet or less of painted surface outdoors is treated differently, but only when none of the prohibited work practices are used and the work does not involve demolition of painted surface areas. Removing a painted component counts its whole surface as disturbed.
The prohibited practices are the part that changes how an old gate gets repaired. WAC 365-230-330 prohibits open-flame burning or torching of painted surfaces during a renovation. It prohibits power sanding, grinding, needle guns and abrasive blasting to remove paint unless the machine has a shroud or containment system with a HEPA vacuum attachment that collects dust at the point where it is generated, and it allows heat guns only below 1,100 degrees Fahrenheit. Waste has to be contained as well.
In practice, that means the familiar picture of someone grinding or torching old paint off a gate in the driveway is not how a renovation firm is allowed to do it at a pre-1978 home. The Department of Commerce’s Renovation, Repair and Painting program page explains that firms doing renovation, repair or painting work on pre-1978 homes or child-occupied facilities need firm certification, with a certified renovator who performs or supervises the work.
The rules have exceptions, including for owners working on their own homes. If your home was built before 1978 and the gate has old paint, test the paint and ask any contractor how they will handle it before work starts.
Broken Welds, Loose Pickets and Missing Ornaments
Cracked and broken welds
A cracked weld is a structural problem, not a cosmetic one. Common spots are where pickets meet the top and bottom rails, where rails join the hinge stile, and at the brackets for hinges, latches and operators. A crack that is only ground over and painted will open again. A proper repair grinds the crack out completely, cleans the area to bright metal and rewelds it with full penetration, then dresses and coats the weld.
Welding in place is possible, but heat near old paint burns the coating, falls under the lead rules at older homes and is a fire risk near wood and dry landscaping. Many repairs get a better weld and coating in a shop.
Loose, bent and rusted pickets
Pickets come loose when the weld or rivet holding them to the rail breaks, or when rust eats the picket where it passes through the rail. A bent picket can often be straightened if the metal is sound. A picket rusted thin at its base is usually cut out and replaced with new bar of the same size and shape, welded in and finished to match.
Missing or broken ornaments
Finials, scrolls, rosettes and collars are the details that make an iron gate look like iron work. When one breaks or goes missing, the repair is mostly about matching. Stock pieces are available in many common patterns. Unusual pieces may need to be forged or fabricated by hand. A shop that does custom work can usually match a scroll’s curve and bar size, and that is part of what our welding and fabrication services for custom gates cover.
On a gate that will be automated, sharp spear points and ornaments that stick out from the face of the gate deserve a second look, because they can create hazards on a moving gate. That is covered in the safety section below.
Hinges, Latches and Sag on Iron Gates
Iron gates are heavy, and all that weight hangs on the hinges and the hinge post. Hinge wear is one of the most common reasons an iron gate starts to drag, bind or fail to latch.
- Worn pins and knuckles. A hinge pin that turns metal on metal for years in wet grit wears oval. The gate drops a little, then a little more. Replacing the pins, or the whole hinge, restores the gate’s height.
- Undersized hinges. A gate that has been made heavier over time, with added panels or an operator bracket, can outgrow the hinges it was built with. Upgrading to heavier hinges, or to adjustable hinges that allow fine height and alignment changes, often solves the problem.
- Rusted hinges. Rust inside a hinge both wears it faster and makes the gate harder to move. On an automated gate, a stiff hinge loads the operator and can trigger its obstruction sensing.
- Latches and drop rods. Latches stop lining up when a gate sags or a post leans. Drop rods wear their holes in concrete or pavement wider over time. Re-aligning the gate usually comes before adjusting the latch.
When the hinge post itself leans or moves at its base, hinge work alone will not hold. The post needs to be straightened, reinforced or replaced, often with a new footing. Our guide to gate post installation in Washington explains post sizes, footings and locating utilities before digging.
Iron gate dragging, dropping or refusing to latch?
We check the hinges, hinge post, frame and welds together, then repair the cause in place or in our shop, from new hinge pins to a rebuilt hinge stile or a new post.
Galvanized and Powder Coated Iron Gates
Many newer steel gates are hot-dip galvanized, powder coated, or both. These finishes protect much better than paint alone, but they need their own repair approach.
Repairing galvanized steel
Hot-dip galvanizing coats the steel with zinc, which protects the steel underneath even where the coating is scratched, because the zinc corrodes first. When the zinc is damaged or burned off by welding, the bare area needs to be repaired. ASTM A780, the standard practice for repairing damaged hot-dip galvanized coatings, allows three methods: zinc-based solder, zinc-rich paint and zinc spray (metallizing). The American Galvanizers Association notes that the same practice applies whether the steel is newly galvanized or has been in service for years.
Touch-up has limits. Large damaged areas are better handled by regalvanizing the part, which means removing the gate and sending it to a galvanizing plant, where existing coatings are stripped and the steel is dipped again. That is a bigger job, but on a gate with widespread coating loss it can give the steel a new start.
Repairing powder coating
Powder coating is a baked finish. When it chips, water creeps under the edges and lifts it. Small chips can be cleaned, primed and touched up with a compatible liquid coating; where it lifts in large areas, the gate is stripped and recoated in a shop.
On a gate that is both galvanized and painted or powder coated, the zinc is repaired first and the top coat second, with products compatible with each other.
Repairing an Automated Iron Gate
Many iron driveway gates in our area have an automatic opener. That adds a few things to any repair.
Release and lock out the operator first. Before anyone works on the gate, the operator should be disconnected from power and released for manual use, following its manual. An operator that starts moving while someone is welding or holding a gate can cause serious injury.
Check the operator brackets. The bracket that connects a swing operator arm to the gate, or a slide operator’s rack or chain to the gate frame, takes a load every cycle. Rust at those brackets, a cracked weld or loose bolts lets the arm push at an angle, which strains the gate, the hinge and the operator. A bracket that is moved even slightly also changes how the operator’s limits are set.
Make the gate move freely before blaming the opener. An operator that strains or reverses is often reacting to worn hinges, a drag or a bent rail, and repairing the gate fixes it. Our guide to the swing gate opener in Washington explains how operators are matched to gate weight and length.
Reset and retest after any repair. When weight is added or removed, hinges are replaced, or the gate is re-hung, the operator’s limits and force settings may need adjustment, and the safety devices need to be tested. Photo eyes and edges must still see the full opening, and the gate must stop and reverse as designed. The page on automatic gate safety standards covers UL 325 and ASTM F2200 in more depth.
Wiring. Repairs to the gate itself are not electrical work, but replacing an operator, moving its power feed or adding devices may be, and in Washington that falls under the state electrical rules administered by L&I.
Safety Upgrades When an Old Iron Gate Is Automated
Ornamental iron gates were often designed long before automatic openers were common, and many were never meant to move on their own. When an older iron gate is automated, or when its old operator is replaced, the gate itself may need changes. DASMA’s installer’s guide to ASTM F2200 states that existing manually operated gates that are to be automated must be brought up to the standard, and that the same applies when an older gate operator is replaced with a new one.

For an iron gate, these are the items that most often need work:
- Openings between pickets. DASMA’s gate system safety material shows picket gaps of 2.25 inches or wider as non-compliant up to 6 feet above grade on the gates it illustrates, and shows screened mesh added to the gate to fix it. On slide gates, all openings must be guarded or screened from the bottom of the gate to the top, or to at least 6 feet, so a 2.25-inch sphere cannot pass through the gate or the part of the fence it covers when open. Many older iron gates have wider spacing and need mesh or added bars.
- Protrusions. The DASMA installer’s guide says protrusions are not permitted on gates, with listed exceptions such as top pickets on ornamental gates. Scrolls, decorative elements or hardware that stick out from the face of a moving gate may need to be removed, trimmed or covered. DASMA’s safety brochure also calls for smooth bottom edges.
- Space between the gate and walls or posts. DASMA’s material on swing gates says that where the distance between the open gate and a wall or fixed object is greater than 4 inches but less than 16 inches, entrapment protection is required in that area. Iron gates hung in front of brick or stone pillars often create exactly that gap.
- A separate pedestrian gate. Automatic vehicle gates are for vehicles. People need their own walk gate, which an older property may not have.
Mesh, matching bars and a matching walk gate can usually be built to look like part of the original. Our page on automating an existing gate walks through the full process.
Repair or Replace an Iron Gate?
Most iron gates can be repaired. The question is whether the result will be sound and safe or a patch that keeps coming back:
| Condition | Usually repair | Usually consider replacement |
|---|---|---|
| Rust | Surface rust and light pitting; sound metal underneath | Rust-through on several rails or stiles; tube rotted from the inside |
| Welds | A few cracked welds at pickets or brackets | Cracks at many joints, showing the gate is flexing beyond what it was built for |
| Frame | Slight sag from worn hinges | Frame racked out of square that will not hold its shape after repair |
| Ornaments | Missing or broken pieces that can be matched | Most of the decorative work lost or broken |
| Automation | Gate can be made compliant with mesh, filled gaps and trimmed ornaments | Changes needed for safety would rebuild most of the gate |
| Size and use | Gate still fits the opening and how it is used | The opening needs to be wider for trucks, trailers or fire access, or the gate needs to slide instead of swing |
Cost depends on what the inspection finds, shop time, the finish and any automation changes, so we do not publish general repair prices. Our article on automatic gate repair cost vs replacement explains which factors move the cost either way.
An original iron gate at an older home or farm often cannot be replaced with a stock product that looks the same, which is another reason careful repair is worth it.
Weighing repair against a new iron gate?
We tell you what each path involves for your gate, from shop restoration to a new custom gate built to match, so you can decide with the facts in front of you.
What Owners Can Do and What Needs a Shop
Some iron gate care suits a handy owner. Welding, fabrication and anything involving safety systems or rules does not.
Reasonable owner tasks
- Washing the gate, clearing leaves and needles from the bottom rail and keeping sprinklers off it.
- Touching up small chips on sound paint after light hand cleaning, using a primer and topcoat made for exterior metal.
- Lubricating hinges with a product the hinge or operator maker recommends.
Work that belongs with a fabricator or gate contractor
- Any structural welding: rails, stiles, hinge brackets and operator brackets.
- Replacing pickets, rails or sections, and forging or fabricating matching ornaments.
- Re-hanging a heavy gate, replacing hinges on a heavy leaf, and straightening or replacing posts.
- Full stripping, blasting, galvanizing or powder coating.
- Paint removal on gates at pre-1978 properties, where Washington’s lead rules apply to renovation firms.
- Anything that touches the operator, its wiring, its safety devices or its settings.
Washington requires construction contractors to be registered with L&I, and the registration number must appear in their advertising under RCW 18.27.100. Asking for that number and looking it up on the L&I site is a simple first check before hiring anyone for gate work.
Keeping a Repaired Iron Gate Sound in Washington Weather
Even a good repair needs attention in Western Washington.
- Inspect twice a year. Early fall, before the rains settle in, and spring, after the wet season, are good times to walk the gate with a flashlight, looking at the bottom rail, welds, hinges and post bases.
- Touch up chips right away. A small chip repaired in one afternoon prevents the creeping rust that lifts a coating in sheets.
- Keep water moving. Clear debris from the bottom rail, the hinge area and any track. Keep sprinklers aimed away from the gate. Make sure the ground drains away from posts.
- Look after the hardware. Lubricate hinges as their maker recommends, and replace worn hardware before it lets the gate drop.
- On automated gates, test the safety devices. Photo eyes and edges should be tested on the schedule in the operator’s manual, and after any repair or change to the gate.
For a full season-by-season checklist covering gates and openers together, see our guide to preventive gate maintenance in Washington.
How We Approach Iron Gate Repair
Emerald Gate Systems is a family-owned gate company based at 7557 Alpine Lane in Sedro-Woolley, Washington. We design, fabricate in our own shop, install, automate and service residential, farm and commercial gates across Skagit, Whatcom, Snohomish, Island, San Juan, King and Pierce counties. Our shop works in hand-forged wrought iron, laser-cut steel and Western Red Cedar, which means repairs can be matched to the original work instead of patched with whatever parts are on hand.
Every repair starts with a free on-site consultation. On an iron gate, we check the frame, welds, pickets and ornaments, the finish, the hinges, latches and posts, and, on automated gates, the operator, its brackets and its safety devices. Then we explain what can be repaired in place, what is better done in the shop and whether replacement makes more sense. Because one team handles CAD planning, welding, installation, automation, access control, testing and future service, a repaired gate and its opener are checked together. We install and service LiftMaster, Viking and FAAC operators, and our custom gate design work covers gates built new to match an existing property.
Washington requires contractors to show their registration in advertising: Emerald Gate Systems is registered with the Washington State Department of Labor and Industries as a construction contractor (EMERAGS748D6) and holds an electrical contractor license in the Doors and Gates specialty (EMERAGS747KE).
Frequently Asked Questions
Can a rusted wrought iron gate be repaired?
Yes, in most cases. Surface rust and light pitting are cleaned back to sound metal, primed the same day and recoated. Rails, pickets or stiles that have rusted thin or through are cut out and replaced with new steel of the same size, then welded and finished to match. Only when rust has spread through much of the frame is replacement usually the better choice.
How do you stop an iron gate from rusting again after repair?
Clean all rust off down to sound metal, prime the same day before flash rust forms, and apply a complete coating system made for exterior metal, paying attention to edges, welds and joints. Then keep water moving off the gate: clear leaves from the bottom rail, aim sprinklers away, keep drain holes open and touch up chips as soon as you see them.
Can wrought iron be welded?
Most gates called wrought iron are welded steel, which welds readily once the area is cleaned to bright metal. Cast iron ornaments are brittle and harder to weld, so a cracked casting is often replaced. Hand-forged pieces can usually be repaired or forged to match. On painted gates at older homes, welding and heat near old paint fall under Washington’s lead rules.
Do Washington’s lead paint rules apply to iron gates and fences?
They can. Chapter 365-230 WAC lists fences and railings among exterior building components. At housing built before 1978 and child-occupied facilities, renovation firms that disturb more than twenty square feet of exterior painted surface must follow lead-safe practices, and open-flame torching of painted surfaces is prohibited. Testing the paint first tells you whether lead is present.
Should I repair or replace my wrought iron gate?
Repair usually makes sense when the metal is mostly sound and the problems are surface rust, a few cracked welds, worn hinges or missing ornaments. Replacement is worth considering when rust has gone through several rails, cracks show up at many joints, the frame will not stay square, or the opening needs to be wider or the gate needs to slide.
Does an old iron gate need changes before it is automated?
Often, yes. DASMA’s installer guide to ASTM F2200 says existing manual gates that are automated must be brought up to the standard. On iron gates that commonly means screening or filling wide picket gaps, removing or covering protrusions, providing entrapment protection near walls and pillars, and adding a separate pedestrian gate.