UL 325 Compliance and ASTM F2200 Requirements for Washington Gates
UL 325 compliance is the question behind every automatic gate in Washington: does the operator protect people, and is the gate itself built so it cannot crush, pull in, or fall on anyone. This center explains both standards in plain language, with the numbers that matter and a checklist you can run on your own gate.
Slide gate, elevation. Numbers from UL 325 and ASTM F2200 as summarized by DASMA.
01
UL 325 vs ASTM F2200: two standards, two jobs
Most confusion about gate safety comes from treating UL 325 and ASTM F2200 as one rulebook. They are separate documents written for different parts of the same system, and a gate can pass one while failing the other.
Product standard
UL 325: the operator
ANSI/CAN/UL 325 covers door, drapery, gate, louver, and window operators and systems. For gates, it sets how the operator senses an obstruction, how it reacts, how external sensors are connected and supervised, and what instructions and warnings come with it. Manufacturers submit operators to a nationally recognized testing laboratory, and a model that passes is listed and marked.
Entrapment protection types and minimum quantities
Monitoring of external sensors
Reversal timing, speed and force limits
Usage classes I to IV
Construction standard
ASTM F2200: the gate
ASTM F2200 is the Standard Specification for Automated Vehicular Gate Construction. It governs the gate panel, its hardware, and the fence next to it: how openings are screened, how rollers are guarded, how the gate is stopped and supported, and how pedestrians are kept away from vehicular travel.
Screening of openings and gaps
Guarded rollers and positive stops
Protrusions, barbed wire and latches
Separate pedestrian access
The practical consequence is simple. A brand new listed operator will refuse to run normally if its monitored sensors are missing, because that is a UL 325 problem the operator can detect. The same operator will happily drive a gate with exposed rollers or an unscreened lattice, because those are ASTM F2200 problems no circuit board can see. A safe installation needs both standards checked, by someone looking at the whole gate and not only at the box on the post.
It also matters who each standard binds. UL 325 binds the manufacturer through the listing program, and the installer through the manufacturer's instructions, which carry the standard's installation requirements into the field. ASTM F2200 binds whoever designs, builds, installs, or automates the gate. When a manual gate is automated, the person adding the operator inherits the construction questions too.
02
Is UL 325 compliance required in Washington?
UL standards are voluntary on their own. DASMA, the trade association for door and gate operator manufacturers, describes them as minimum requirements developed through an open process rather than through a government mandate. What turns them into obligations is adoption by code and reference by manufacturers.
1
International Fire Code, Section 503.6. Where security gates are installed across fire apparatus access roads, electric gate operators are required to be listed in accordance with UL 325, and gates intended for automatic operation are required to be designed, constructed and installed to comply with ASTM F2200.
2
Washington adoption. Washington adopts the International Fire Code statewide through WAC 51-54A, and local fire marshals enforce it, often with their own access and override requirements.
3
Manufacturer instructions. Every listed operator ships with instructions that require the protection the standard calls for. Installing it any other way puts the installation outside the listing.
For property owners the takeaway is not legal theory. If your gate crosses a fire access road, a fire marshal can ask to see a listed operator and a compliant gate. If it does not, the same two standards are still what manufacturers, inspectors, and insurers use as the recognized measure of a safe installation. We cover the fire side in more depth, including Knox boxes and strobe sensors, in our guide to fire department gate access in Washington, and permit questions in what permits an automatic gate needs in Washington.
03
UL 325 requirements: the two independent means rule
The heart of UL 325 for gates is Section 32 and its two tables. Section 32.1.1 says a vehicular gate operator must have provisions for, or be supplied with, a minimum of two independent entrapment protection means for each entrapment zone, and must only operate after the minimum number of means has been installed and enabled. The rule that trips up most installations sits in the note under Table 32.1: the same type of device cannot be used for both means. Two photo eyes in the same zone count as one type.
Pick a gate type to see the minimum quantity of entrapment protection means (UL 325, Table 32.2)
2Opening
2Closing
Allowed types: A, B1, B2 or D
Two independent means in each direction of travel. A typical layout pairs the operator's inherent sensing (Type A) with external monitored sensors (Type B1 or B2) covering both the opening and closing paths.
Minimum quantity of entrapment protection means, reprinted by DASMA from the 7th edition of UL 325
Gate operator
Opening
Closing
Allowed types (Table 32.1)
Horizontal slide gate
2
2
A, B1, B2 or D
Horizontal swing gate
2*
2*
A, B1, B2, C or D
Vertical pivot gate
2
2
A, B1, B2 or D
Vertical lift gate
1
2
A, B1, B2 or D
Horizontal bifold gate
2
2
A, B1, B2 or D
*For a swing gate, two means are required in each direction of travel, except that if there is no entrapment zone in one direction, one means is enough in that direction while the other direction still needs two. A single device may cover both the opening and closing directions. Source: DASMA TDS 353.
In practice this is why almost every slide gate installed today has at least one photo eye or edge for the closing path and another for the opening path, where the gate runs back past a fence, a wall or a planter. The operator's own inherent sensing counts as one means, the external device counts as the second, and the operator checks that the external device is present before it will run normally. Barrier arms are treated separately: according to the 2016 revision summary, an arm installed so it never comes closer than 16 inches to a rigid object is not required to protect against entrapment.
Counting zones is the installer's job, not the manufacturer's. A long slide gate that passes a building on its way open may have two separate opening zones, and each needs its own coverage. A swing gate whose leaves open toward a wall, a hedge or a parked car has an opening zone the brochure diagram never showed. This is the most common reason a gate that "has a photo eye" is still not compliant.
Not sure how many zones your gate has?
We walk the gate's full travel path, count every entrapment zone, and tell you exactly what is covered and what is not.
UL 325 entrapment protection types A, B1, B2, C and D
UL 325 names five kinds of entrapment protection for gate operators. The letters show up in operator manuals, on sensor packaging and in inspection notes, so it helps to know what each one actually does.
Type A
Inherent entrapment protection
Built into the operator. It detects that the gate has met resistance and reacts. It only knows something is wrong after contact, which is why it is never enough alone.
Type B1
Non-contact sensor
A photoelectric sensor or equivalent. The beam across the opening breaks before the gate touches anything. Placement and alignment decide whether it actually protects.
Type B2
Contact sensor
An edge device or equivalent on the leading or trailing edge. It reacts the moment it is pressed, wired or wireless, and must sit where an object would actually be caught.
Type C
Inherent force limiting
An inherent force limit, adjustable clutch, or pressure relief device. Allowed only for swing gates and barrier arms, and a swing gate using it may not exert more than 40 pounds at the leading edge.
Type D
Continuous pressure control
The gate moves only while someone holds the control, from a spot with a full view of the gate. No other activation device may be connected, and automatic closing is not allowed.
Retired
Type E is gone
An audible alarm used to be listed as a type. Since January 12, 2016, it no longer counts as entrapment protection, because an alarm warns and does not protect. The words "primary" and "secondary" were dropped at the same time.
The combination matters more than the individual parts. A swing gate operator might use inherent sensing as one means and a monitored edge as the second. A slide gate might rely on two different external devices in a tight zone where inherent sensing reacts too late. Whatever the mix, two devices of the same type in one zone do not make two means.
If you want the field detail on each device, we wrote separate guides on photo eye placement, where safety edges go, and loop detectors versus exit wands. Loops are worth a note here: a vehicle loop detects cars for convenience and logic, but it is not one of the entrapment protection types, because it does not see a person standing in the gate's path.
05
How UL 325 changed: the 2016 and 2018 revisions
Many gates in Northwest Washington were installed before the current rules, which is why "it was fine when it went in" is often true and still not the end of the story.
1973
First edition
UL 325 is released, focused on electric garage door operation, with no provisions for gates.
Early 1990s
Gates enter the standard
Gate operator manufacturers within DASMA initiate vehicular gate operator provisions in UL 325.
2000
Two independent devices
Gate operators are required to have two independent entrapment protection devices for each area that requires protection.
Jan 12, 2016
Monitoring and the end of Type E
External non-contact and contact sensors must be monitored every cycle for correct connection and correct operation. If a device is missing, faulty, or shorted, the operator runs only by constant pressure, and portable remotes stop working. Type E stops counting, "primary" and "secondary" are dropped, the barrier arm distance changes from 2 feet to 16 inches, an audio alarm after two successive obstructions becomes required for all classes, and an emergency exception lets controls for fire, police, or EMS sit anywhere in line of sight.
Aug 2018
Two means in each direction
A minimum of two independent means is required in each direction of travel where entrapment risk exists, monitoring components must be factory installed inside the external devices, and slide gate operators need at least two monitored external devices connected, one for the open cycle and one for the close cycle.
Today
7th edition
DASMA's current data sheet reprints Tables 32.1 and 32.2 from the 7th edition of UL 325 and states plainly that all external means of entrapment protection must be monitored.
The 2016 change is the one owners feel. Before it, a photo eye could be wired to almost any operator, and a dead or disconnected sensor simply stopped protecting while the gate kept running. Since 2016, the operator verifies every external device at least once per open and close cycle. When a sensor fails, the gate does not quietly keep cycling; it drops to constant pressure operation for the protected direction. If your remote stopped working and the keypad only moves the gate while you hold it, a monitored device has probably failed. We list this and other symptoms in why an automatic gate stops opening or closing.
The standard is also explicit that nobody may modify the system in the field to bypass, interfere with, or defeat monitoring, whether with wires, jumpers, switches, or components. A jumper across the sensor terminals turns a protected gate into an unprotected one that looks normal from the driveway.
06
UL 325 gate classes I to IV: which one is your property?
Operators are listed for usage classes. The class is chosen by the property and its users, not by the size of the gate, and installing an operator outside its listed class is a mismatch even if every sensor works.
A vehicular gate operator intended for use in garages or parking areas associated with a residence of one to four single families. Typical here: a driveway gate on acreage near Sedro-Woolley, or a shared gate serving up to four homes.
A gate operator for a commercial location or building such as a multi-family housing unit with five or more single family units, a hotel, garages, a retail store, or other buildings accessible by or servicing the general public. HOA and apartment entrances usually land here.
A gate operator for an industrial location or building such as a factory or loading dock area, or other locations not accessible by or intended to serve the general public. Equipment yards and warehouses with controlled staff access fit this class.
A gate operator for a guarded industrial location such as an airport security area, or other restricted access locations not servicing the general public, where unauthorized access is prevented through supervision by security personnel.
Two details catch owners out. First, the line between Class I and Class II is the number of homes: a private road gate serving five homes is not residential under these definitions. Second, use changes. A farm gate that becomes the entrance to a farm stand open to the public, or a shared road that gains a fifth household, may need an operator listed for a different class. ASTM F2200 uses the same four classes for construction, and some of its provisions do not apply to Class IV gates, where security is prioritized. Communities planning a shared entrance will find the planning side in our guide to gate and access control systems for HOAs, condos and apartments.
Not sure which class your property falls under?
We look at who uses the gate and how, and match the operator to the property before anything is ordered.
Where entrapment zones are on slide and swing gates
UL 325 defines entrapment as the condition when a person is caught or held in a position that increases the risk of injury. The places where that can happen are the entrapment zones, and every one of them needs its protection.
Slide gate. The closing zone is between the leading edge and the receiving post. The opening zone is where the trailing edge runs back past the fence, a wall, or anything parked near it. Each needs coverage in its direction of travel.Swing gate. Entrapment happens at the meeting edges while closing, and between an opening leaf and any fixed object it swings toward. ASTM F2200 sets a minimum clearance to fixed objects in the open position, which DASMA's installer guidance gives as 16 inches, or the zone must be protected with sensors.
Vertical lift gates have the mirror problem of a garage door: the dangerous direction is down, which is why Table 32.2 asks for two means while closing and one while opening. Vertical pivot gates sweep an arc overhead and down, and both directions count. On slide gates with a cantilever design, the counterbalance tail that runs back behind the opening creates its own opening zone, a detail we explain in our cantilever gate installation guide. And for drivers the hazard usually sits in the closing path: the moment a car is across the threshold while the gate starts to close.
08
What a UL 325 listed gate operator must do
Beyond counting sensors, the standard sets how a listed operator behaves when something is in the way. These are the numbers DASMA summarizes from UL 325, and they are a quick way to tell whether an existing gate behaves like a compliant one.
2seconds
After sensing an obstruction, reversing must begin within 2 seconds, so nobody is held against a stopped gate.
2inches
After the first contact, the gate must reverse and travel at least 2 inches.
1foot per second
Class I and II slide gate operators, and vertical lift operators, may not exceed this speed when pulling 75 pounds or more.
40pounds
A swing gate using Type C may not exert more than 40 pounds at the leading edge of the shortest recommended gate length, two seconds after start-up.
2ndobstruction
If inherent sensing detects a second sequential obstruction, the gate must stop, sound an audio entrapment alarm, and stay stopped until an intended hardwired input is received. Someone in sight of the gate has to see and clear the cause.
Timerdisabled
After any stop or reversal by a Type A or B2 device, the timer-to-close is disabled until reset, so a gate that just touched someone cannot close itself again a few seconds later.
Manufacturers are also required to name the brand and model of external sensors that are compatible with each operator. That is why "any photo eye will do" is wrong on a modern gate. A sensor that is not on the operator's compatibility list may not be monitored correctly, and the system may reject it or, worse, accept it without the supervision the standard assumes. When we compare operators in our gate operator brand comparison, sensor compatibility is one of the first things we check.
09
ASTM F2200 requirements for automated gate construction
ASTM F2200 divides automated vehicular gates into horizontal slide, horizontal swing, vertical lift, vertical pivot, and overhead pivot designs, each with its own construction rules, plus general requirements that apply to all of them. These are the provisions that most often decide whether an existing gate can be automated as is.
2¼ in
Openings, up to 72 inches
On slide gates, openings are guarded or screened so a 2¼ inch sphere cannot pass through, from the bottom of the gate to at least 72 inches above grade, or the full height on a shorter gate. DASMA notes the height moved from 48 to 72 inches in the 2011 revision to account for reach.
2¼ in
Gap to the support structure
The gap between a moving slide gate panel and its support structure is limited. The rationale cites cases of people riding a slide gate and being pulled into that gap.
8 ft
Guarded rollers
Weight-bearing exposed rollers 8 feet or less above grade are guarded or covered, guide wheels and V-groove rollers included.
45°
Cannot fall over
A gate detached from its supporting hardware must not fall more than 45 degrees from vertical, using support posts, brackets, cables or chains.
Stops
Positive stops
Slide gates need positive stops that limit travel to the designed fully open and fully closed positions, at the top or bottom of the gate.
½ in
Smooth bottom edge
The bottom edge stays free of protrusions; hardware such as bolts may not project more than half an inch and must be smooth.
8 / 6 ft
Barbed tape and wire
Barbed tape only at 8 feet or higher above grade, barbed wire only at 6 feet or higher, so a moving gate does not drag a hazard past people.
9 in²
Receiver guides
A slide gate's receiver guide sits behind the leading edge of the receiver post or above 8 feet, or has a cross section over 9 square inches, so it is not a puncture hazard.
No latch
Manual latches come off
A latch made for padlocks and chains becomes a protrusion once the gate is powered and is removed before automation; a receiver guide replaces it where needed.
Swing gates have a different set of concerns. Hinges and hardware are allowed, but the area where a leaf can crush against a fixed object is restricted, and the gate needs clearance from walls, fences, and buildings in the open position or electronic protection for that zone. Vertical lift gates need screening of the area covered during travel, limited gaps between the moving frame and fixed objects, and a means of preventing over-travel so the gate cannot leave its guides. Vertical pivot gates need smooth framing, screening where the arm sweeps, and enough lateral stability to enter a receiver guide so nobody can push the gate sideways to get in.
Notice what is missing: ASTM F2200 is not a style guide. Ornamental pickets and scrolls at the top are allowed as long as they stay within the vertical plane of the gate. What the standard cares about is reach-through, pull-in, crushing, falling, and puncture. That is why a beautiful wrought iron gate often needs mesh or screening on its lower section before it can be automated, a topic we cover with materials in wrought iron gate repair and vertical pivot gates.
Sources: DASMA technical data sheets TDS 353 and TDS 370 (Rationale Behind the Provisions of ASTM F2200). The standard itself is available from ASTM; always check the current edition and the operator manufacturer's instructions.
Wondering if your gate can be automated as it is?
We measure openings, rollers, stops and gaps on site and tell you what the gate needs before an operator goes on.
Gate controls, warning signs and pedestrian access
Some of the most effective safety rules have nothing to do with sensors. They decide where people stand, what they can reach, and where they walk.
Site plan, top view. Vehicles use the automated gate; people use their own gate and path.
1
6 feet
Controls out of reach
All gate activation controls must be at least 6 feet from the gate, so nobody can reach through the gate to operate it. The 2016 exception allows emergency controls accessible only to fire, police, or EMS anywhere in line of sight of the gate. Placement on the approach is planned together with the keypad pedestal location.
2
2 signs
Warning signs on both sides
A minimum of two warning signs must be displayed in the area of the gate, visible from both sides of the opening. UL 325 specifies their format, content and placement, and the operator manufacturer supplies them.
3
Separate
Pedestrians get their own gate
Vehicular gate operators may only be used on vehicular gates, never on pedestrian gates, and separate pedestrian access must be provided wherever people are likely to walk in or out. See our pedestrian gate access control guide for locks and ADA details.
Type D installations add their own rule: the control has to be placed where the user sees the whole gate area while it moves, a placard goes next to it, no other activation device may be connected, and no automatic closing is allowed. That makes constant pressure useful in a few supervised settings, and a poor fit for a busy driveway.
Pedestrian access deserves emphasis because it is the rule owners most often skip to save money. People walk through a vehicular opening because it is there. A separate pedestrian gate gives them a path that keeps them out of the vehicular gate's travel and out of the way of cars, and on commercial and multi-family sites it is also where accessibility requirements come in, which we address in our page on ADA entry requirements in Washington.
11
UL 325 and ASTM F2200 self-check for your gate
This checklist is a quick way to see where your gate stands. It is not an inspection, and a gate that passes every item can still have a zone only a technician will spot, but a gate that fails several items almost certainly needs attention. Nothing you tick here is saved or sent anywhere.
0/14
Operator (UL 325)
Gate (ASTM F2200)
Site
Tick what your gate already has. Unticked items are where to start.
Two of these items are worth testing carefully rather than assuming. The unplug test should only be done by someone who knows how to restore the wiring, and the reversal test should be done with a soft object such as a cardboard box, never a hand, a foot or a pet. If you are unsure, a technician can run both in a few minutes as part of routine service, the kind of visit described in our Washington automatic gate maintenance guide.
12
Bringing an older gate up to UL 325 and ASTM F2200
DASMA's rationale for ASTM F2200 is direct about two situations. When a UL 325 compliant operator is installed on an existing vehicular gate, the gate may need to be upgraded. When an existing operator is replaced with a compliant one, the gate should be upgraded as needed. In other words, the moment a new operator goes on, the construction questions come back.
1
Identify the operator and its class
Find the listing label and model, confirm the class fits the property, and check what external sensors the manufacturer lists as compatible.
2
Walk the full travel path
Mark every place a person could be caught while opening and while closing, including the trailing edge, fixed objects, and anything added since the gate went in.
3
Check the gate itself
Measure openings in the lower 72 inches, look at rollers, stops, receiver guides, the bottom edge, latches, and how the gate is held if a hinge or roller fails.
4
Plan sensors and screening together
Choose monitored devices of different types for each zone, add mesh or screening where needed, and fix gaps at posts before tuning sensitivity.
5
Controls, signs and pedestrians
Move controls that are within reach of the gate, install the warning signs, and give people their own way through.
6
Test and document
Test every device in both directions, confirm monitoring works by simulating a fault, and leave the owner a record of what was installed and why.
Upgrading is rarely all or nothing. Many older gates in good structural condition need screening on the lower section, a pair of monitored sensors, positive stops and new signs, and the operator stays. Others have an operator so old that no compatible monitored sensor exists, and the honest answer is a new operator. If you are weighing those options, our article on repairing versus replacing an automatic gate walks through the decision, and automating the gate you already have covers the case where the gate is manual today.
Have an older gate you want brought up to current standards?
We evaluate gates we did not install, and we tell you what can stay and what has to change.
We design, fabricate, install, automate, and service gates as one team from our shop in Sedro-Woolley, across Skagit, Whatcom, and Snohomish counties and the islands. Because the same people who weld a gate also wire its operator, construction and operator safety are planned together from the first drawing rather than patched at the end.
Fabrication with F2200 in mind
Screening, smooth bottom edges, roller guards, stops and receiver guides are part of the design in our own shop, not add-ons after the gate is hung.
Licensed for gate electrical
We hold a Washington electrical contractor license in the Doors and Gates specialty, so operator wiring and sensors are installed by a licensed contractor.
Gates we did not build
We service and evaluate existing gates from every brand, including LiftMaster, Viking and FAAC operators, and we will not bypass a safety device to make a gate run.
Emerald Gate Systems LLC, Washington construction contractor registration EMERAGS748D6 and electrical contractor license EMERAGS747KE (Doors and Gates specialty).
Frequently asked questions about UL 325 compliance
What does UL 325 compliance mean for a gate?
It means the gate operator is listed to UL 325 and installed the way its instructions require, with at least two independent means of entrapment protection of different types for each entrapment zone, monitored external sensors, controls at least 6 feet from the gate, and warning signs on both sides.
What are the ASTM F2200 requirements for an automatic gate?
ASTM F2200 covers construction: screening so a 2¼ inch sphere cannot pass through openings up to 72 inches on slide gates, limited gaps at support posts, guarded rollers below 8 feet, positive stops, a gate that cannot fall more than 45 degrees, smooth bottom edges, and separate pedestrian access.
Is ASTM F2200 the same as UL 325?
No. UL 325 is a product standard for the operator and its entrapment protection, tested by a laboratory. ASTM F2200 is a construction standard for the gate and adjacent fence. They are harmonized and reference each other, but a listed operator does not make a gate compliant with ASTM F2200.
Are UL 325 and ASTM F2200 required by law in Washington?
The International Fire Code, adopted in Washington through WAC 51-54A, requires electric gate operators on fire access roads to be listed to UL 325 and automatic gates to comply with ASTM F2200. Elsewhere they remain the recognized standard of care used by manufacturers, inspectors, and insurers.
Can I use two photo eyes as my two means of protection?
Not in the same zone. UL 325 says the same type of device cannot be used for both entrapment protection means. Two photo eyes are both Type B1, so a zone protected only by photo eyes still needs a different type, such as the operator's inherent sensing or a contact edge.
Why does my gate only move while I hold the button?
On operators built to the 2016 and later rules, a missing, disconnected, or faulty monitored sensor drops the gate to constant pressure operation for the protected direction, and remotes stop working. It is a safety response, and the fix is to repair or replace the sensor, not to bypass it.
Do I need a separate pedestrian gate?
Where people are likely to walk in or out, yes. Vehicular gate operators may only be used on vehicular gates, and UL 325 and ASTM F2200 both call for separate pedestrian access so people stay out of the moving gate's path and away from vehicles.
Does an older gate have to be replaced to comply?
Usually not. Many older gates can be brought up with screening, monitored sensors, positive stops, roller guards, relocated controls, and signs. Replacement makes sense when the gate is structurally unsound or the operator cannot accept any compatible monitored sensor.