Climate and terrain atlas

Northwest Washington Climate Atlas for Gates

Rain, freeze, wind, water, and ground decide how a gate ages long before style does. This atlas puts official numbers for Skagit, Whatcom, Snohomish, Island, San Juan, King, and Pierce counties side by side, then shows what each one changes in a gate, its footings, and its operator.

Average annual precipitationinches per year

NOAA NCEI 1991 to 2020 Climate Normals, 12 stations across the service area. Hover a gauge for the station.

County explorer

Pick a county to see its numbers

Each county shows its NOAA climate stations, the hardiness zone for its main towns, the frost depth and design wind speed published by a local building department where we could find one, and what we look at on a gate there.

Tiles are arranged by rough position, north at the top, not drawn to scale.

Skagit County

0inches of precipitation a year

0nights a year at or below 32°F

0°F average January low

0inches of snow a year

Hardiness zone
Frost depth
Design wind speed

What we look at here

    See every station in one table
    NOAA NCEI 1991 to 2020 Climate Normals for stations in the Emerald Gate Systems service area
    CountyStationAnnual precipitation (in)Annual snowfall (in)January avg low (°F)Nights ≤ 32°FJuly avg high (°F)
    WhatcomBellingham Intl Airport34.71no normal34.058.672.7
    WhatcomBellingham 3 SSW35.953.434.843.375.1
    SkagitSedro-Woolley48.535.734.746.274.5
    SkagitConcrete PPL Fish Station71.2416.333.447.375.6
    SnohomishEverett (estimated precipitation normal)40.25no normal34.651.374.8
    SnohomishEverett/Snohomish County Airport33.37no normal36.628.872.3
    IslandCoupeville 1 S21.742.536.632.470.1
    San JuanFriday Harbor Airport18.47no normal37.140.172.4
    San JuanOlga 2 SE29.185.838.031.969.2
    KingSeattle-Tacoma Intl Airport39.346.337.725.277.4
    PierceTacoma #140.81no normal37.427.276.8
    PierceBuckley 1 NE48.314.333.950.176.6

    "No normal" means NOAA did not publish a 1991 to 2020 snowfall normal for that station. Snowfall normals that do exist are flagged provisional by NOAA. The Everett precipitation value carries NOAA's estimated flag; the nearby airport value is listed for comparison.

    County by county

    Seven counties, seven different gate climates

    The same numbers as the explorer, read the way we read them before a site visit.

    Skagit

    Sedro-Woolley rain
    48.53 in
    Concrete rain
    71.24 in
    Concrete snow
    16.3 in

    From bay farmland to the upper valley

    Our home county shows the widest spread in the atlas. Sedro-Woolley averages 48.53 inches of precipitation and 46.2 frost nights a year, while Concrete, farther up the valley, averages 71.24 inches and 16.3 inches of snow, the most of any station here. The Skagit River's flood record, kept by the USGS near Concrete, reaches back to 1897. A gate on the delta flats and a gate in the upper valley face different water, different ground, and different winters, even though they are in the same county.

    Whatcom

    frost nights, Bellingham AP
    58.6
    rain, Bellingham AP
    34.71 in
    Feb 2021 outflow gusts
    71 mph

    The coldest nights and the outflow wind

    Bellingham International Airport averages 58.6 nights a year at or below freezing, the most of the 12 stations, while Bellingham 3 SSW averages 43.3. Precipitation is moderate at about 35 inches. What sets Whatcom apart is the Fraser outflow: in February 2021 it brought gusts up to 71 mph on the Lummi Reservation and a 21°F reading in Bellingham. Wind, cold, and the November 2021 Nooksack flooding are the three things we plan around here.

    Snohomish

    frost nights, Everett
    51.3
    frost nights, Paine Field
    28.8
    frost depth, City of Snohomish
    18 in

    Two stations, two different winters

    The Everett co-op station averages 51.3 frost nights a year; Everett/Snohomish County Airport averages 28.8. Their January lows differ by two degrees, 34.6°F against 36.6°F. That gap is a reminder that a station is a point, not a county. The City of Snohomish lists an 18-inch frost line depth, the deepest published value we found, and NWS Seattle notes that the convergence zone generally forms north of Seattle, which puts this stretch of Puget Sound in its path.

    Island

    rain, Coupeville
    21.74 in
    county design wind
    110 mph
    county frost depth
    12 in

    Dry, mild, and exposed

    Coupeville averages 21.74 inches of precipitation, the second lowest in the atlas, with a January average low of 36.6°F and 32.4 frost nights. Island County lists a 110 mph design wind speed and a 12-inch frost depth, and the City of Oak Harbor lists a 115 mph ultimate wind speed. On Whidbey and Camano, wind and salt usually shape a gate more than rain does.

    San Juan

    rain, Friday Harbor AP
    18.47 in
    January low, Olga
    38.0°F
    hardiness zone, Friday Harbor
    9a

    The driest station, the mildest nights

    Friday Harbor Airport averages 18.47 inches a year, the lowest of all 12 stations, and Olga 2 SE has the mildest January lows at 38.0°F. Friday Harbor is in hardiness zone 9a. The county lists a 12-inch frost depth and a 110 mph design wind speed. Rain is less of a problem than salt air, exposure, and the fact that every part and every service visit arrives by ferry.

    King

    frost nights, Sea-Tac
    25.2
    rain, Sea-Tac
    39.34 in
    Seattle design wind
    98 mph

    The fewest frost nights

    Seattle-Tacoma International Airport averages 25.2 nights at or below freezing, the fewest in the atlas, and 39.34 inches of precipitation, with a January average low of 37.7°F. The City of Seattle's 2021 residential code table lists a 12-inch frost line and a 98 mph design wind speed. On close-in lots, utilities, pavement drainage, and access control usually decide more about a gate than climate does.

    Pierce

    frost nights, Tacoma
    27.2
    frost nights, Buckley
    50.1
    rain, Buckley
    48.31 in

    City and foothills

    Tacoma #1 averages 40.81 inches of precipitation and 27.2 frost nights. Buckley 1 NE, in the foothills, averages 48.31 inches, 4.3 inches of snow, and 50.1 frost nights, close to double Tacoma's frost count. The City of Lakewood lists a 12-inch minimum frost line depth. A gate in Tacoma and a gate near Buckley belong in different rows of the spec matrix below.

    Your lot

    A station is not your driveway

    Elevation, slope, shade, trees, and distance from water can move a site well away from the nearest station. That is why the numbers start the conversation and the site visit finishes it.

    Book a site visit

    The wet season

    When the rain falls, month by month

    Annual totals hide the pattern that matters for a gate project: almost all of the water arrives in a few months. Pick a station to redraw the year.

    October to MarchApril to September

    0%of the year's precipitation falls October through March

    November leads everywhere

    November is the wettest month at every one of the 12 stations in this atlas, and July or August is the driest. At Concrete, November alone averages 11.49 inches, more than half of what Friday Harbor Airport receives in an entire year.

    What that means for a project

    Trenching, concrete footings, and conduit runs are easiest when the ground is drier, which in most of the region means late spring through early fall. Work can and does happen in winter, but trenches fill with water, soil gets soft, and concrete needs protection, so we plan the schedule around it.

    What it means for the gate

    Months of steady rain test every enclosure, splice, and hinge. Water that cannot drain away from an operator pad or out of a slide track will sit there for weeks. Drainage, sealed connections, and finishes that tolerate constant wetness matter more here than in drier climates.

    Want a gate specified for your exact site?

    We look at drainage, exposure, footing depth, and power on site before recommending a gate or an operator.

    Freeze

    How often it freezes, station by station

    Snow totals are small at most stations, but frost is routine. Each dot is one night a year, on average, when the low reaches 32°F or colder.

    Frost is a mechanics problem

    Repeated freezing and thawing works water into hinges, latches, and slide tracks, and ice on a track or a frozen hinge loads the operator. The five stations with the fewest frost nights are all coastal or urban: Sea-Tac, Tacoma, Paine Field, Olga, and Coupeville. Inland and northern sites freeze far more often, and that is often where a cold morning and a long driveway arrive together.

    Batteries feel the cold

    Battery backups and solar systems deliver less on cold mornings, and the coldest mornings tend to come with the shortest days. On a battery or solar gate in Whatcom, Skagit, or the foothills, the backup should be sized for a cold, dark January, not for an average day. See solar gate automation sized for Washington winters.

    Snow is local

    Concrete averages 16.3 inches of snow a year, the most of any station here with a published normal, while Coupeville averages 2.5. Higher ground and the foothills see more. Sliding gates need a track that can be cleared, and swing gates need room to swing over what is left; our guide to driveway gates for snow in Washington covers the details.

    Wind

    Wind: outflow, convergence, and design speeds

    A gate is a wall that moves. In wind, a solid panel behaves like a sail, and the hinges, operator, and posts carry the load.

    Fraser River outflow

    In winter, cold air can pour out of the Fraser River Valley into Whatcom County. The Office of the Washington State Climatologist described a February 2021 event in which outflow produced gusts up to 71 mph on the Lummi Reservation and dropped Bellingham's temperature to 21°F. Outflow brings wind and hard cold at the same time.

    Puget Sound Convergence Zone

    The National Weather Service in Seattle explains that the convergence zone forms when strong westerly winds flow around the Olympic Peninsula and meet again over Puget Sound. It generally forms north of Seattle and can move south toward Boeing Field or Sea-Tac, bringing bursts of heavy showers and gusty, shifting wind.

    Design wind speeds published by local building departments

    San Juan County110 mph2018 code handout
    Island County110 mph2018 code table, effective 2021
    City of Oak Harbor115 mphultimate wind speed
    City of Snohomish110 mph2018 codes, Exposure B or C by site
    City of Seattle98 mph2021 Seattle Residential Code

    These are the structural design values each jurisdiction lists for buildings under the code edition named. They are not forecasts, and codes are updated, so the current value comes from the building department for the specific address. They are useful here as a comparison: exposed islands and shorelines are designed for more wind than sheltered inland lots. Our guides to driveway gates for windy areas and privacy driveway gates cover how that changes the design.

    Water

    Atmospheric rivers and river valleys

    The biggest water events here are not ordinary rain. They are concentrated storms that arrive off the Pacific and can push rivers over their banks.

    What an atmospheric river is

    NOAA describes atmospheric rivers as relatively long, narrow regions in the atmosphere that transport most of the water vapor outside the tropics. When one stalls over western Washington, rain totals that would normally take weeks can arrive in days.

    November 2021

    The Office of the Washington State Climatologist reported five atmospheric river events affecting Washington in November 2021, with major flooding on the Nooksack and Skagit rivers. Bellingham set a daily rainfall record of 2.78 inches on November 14.

    The Skagit's long record

    According to the U.S. Geological Survey, the four largest recorded peaks on the Skagit River near Concrete date from 1897, 1909, 1917, and 1921. Floods since then have still been large: USGS lists a peak of 153,000 cubic feet per second in 1949 and 166,000 cubic feet per second on October 21, 2003.

    about 240,000Dec 1921 (as originally published)
    166,000Oct 2003
    153,0001949
    Peak flow, cubic feet per second, Skagit River near Concrete. USGS later revised the published 1921 figure 5 percent lower.

    Keep electronics above the water line

    On valley floors and low lots, operators, control boxes, and battery backups belong on raised pads or posts, and the low point of the driveway should not be where the control box sits.

    Seal the underground

    Conduits, splices, and vehicle loops live underground, where water finds them. Sealed connections and conduit that drains away from equipment prevent most wet-season faults. See gate opener wiring in Washington.

    Plan the outage

    Storms that bring flooding often bring power outages too. Battery backup and a known manual release keep the property reachable; more in battery backup for automatic gates.

    Building on a slope, a valley floor, or an island?

    We design footings, drainage, and gate structure for the ground and exposure at your address.

    Ground

    Footings, frost lines, and glacial soils

    A gate post is only as straight as the ground under it. Two things set the footing: how deep frost can reach, and what the soil is made of.

    Frost depth published by local building departments

    12 inSan Juan County"Frost Depth: 12 inches (bottom of footings)," 2018 code handout
    12 inIsland Countyfrost line depth, 2018 code table effective 2021; City of Oak Harbor also lists 12 inches
    12 inCity of Seattle2021 Seattle Residential Code, Table R301.2
    12 inCity of Lakewood, Pierce County"Frost Line Depth = 12 inches minimum"
    18 inCity of Snohomish"Frost Line Depth: 18 inches," 2018 code information
    AskSkagit and Whatcomwe did not find a frost depth in the county handouts; confirm with the building department for the address

    Code frost depth is a minimum for buildings. Gate posts and operator pads carry a different load, a heavy leaf hanging off one side, so post footings are designed for leverage and soil, and they usually go deeper than the frost line alone would require.

    Till and outwash

    Much of the Puget Lowland was shaped by glaciers. The USGS describes glacial till as typically impermeable, laid down beneath the ice sheet itself, and outwash as permeable sand and gravel laid down by water flowing from the ice. Till drains poorly and digs hard; outwash drains fast and can be loose.

    River-bottom ground

    The USGS also maps large areas of alluvium, river-deposited sediment, across the lowland. On valley floors such as the Skagit and Nooksack flats, soft and wet soils call for wider footings, drainage, and a closer look before a heavy gate goes in.

    Hardiness zones

    The 2023 USDA Plant Hardiness Zone map puts Bellingham, Mount Vernon, Sedro-Woolley, Everett, Coupeville, Oak Harbor, Tacoma, and Buckley in zone 8b, the east side of Bellingham and Concrete in 8a, and Friday Harbor and Seattle in 9a. The zone tracks the coldest nights, the ones that freeze hinges and test batteries.

    Planning calendar

    How the seasons shape a gate project

    The rain curve above is also a project calendar. This is how we line up design, fabrication, and site work against it.

    Winter: design and fabrication

    The wettest, darkest months are well suited to the parts of a project that happen indoors: site measurements taken between storms, CAD drawings, approvals, and fabrication in our Sedro-Woolley shop. A gate built in winter is ready to install when the ground firms up.

    Spring: footings and trenching

    As monthly rainfall drops through April and May, trenches stay open, soil compacts, and concrete cures without fighting standing water. It is the natural start of the site-work season.

    Summer: the driest window

    July or August is the driest month at every station in the atlas. Long trenches, conduit runs to distant gates, solar installations, and work on sloped or soft ground are easiest now, and it is the best time to test drainage before the rain returns.

    Fall: before the storms

    October and November bring the rain back fast; November is the wettest month at every station. Fall is the time to finish site work, check seals and batteries, clear tracks and drains, and make sure every automatic gate is ready for its first outage of the season.

    Winter installations still happen, especially repairs, replacements, and urgent security work. They take more care: dewatering trenches, protecting fresh concrete from cold, and scheduling around storms.

    Spec matrix

    What changes in a gate from zone to zone

    Four broad settings cover most properties in the service area. Pick one to see how we adjust each part of a gate. This is our working guidance, built on the numbers above; every site still gets its own look.

    Materials and finish

    Structure and wind

    Footings and ground

    Operator and power

    Water and drainage

    Material choices are covered in depth in choosing gate materials for Washington weather, with coastal specifics in best gate materials in Anacortes and corrosion-resistant waterfront gates in Edmonds. Island logistics are in automatic gates on Whidbey Island.

    Planning next season's gate now?

    Design and fabrication can start in the wet months so site work is ready when the ground is.

    Sources and method

    Where these numbers come from

    Every figure on this page comes from a public, primary source. Here is what we used and how to read it.

    1. NOAA NCEI 1991 to 2020 Climate Normals

      Annual and monthly normals for 12 stations: Bellingham International Airport, Bellingham 3 SSW, Sedro-Woolley, Concrete PPL Fish Station, Everett, Everett/Snohomish County Airport, Coupeville 1 S, Friday Harbor Airport, Olga 2 SE, Seattle-Tacoma International Airport, Tacoma #1, and Buckley 1 NE. Normals are 30-year averages, not forecasts. NOAA flags some values as estimated or provisional; we note those where they appear. ncei.noaa.gov

    2. Local building department design criteria

      Frost depth and design wind speed as published by San Juan County, Island County, the City of Oak Harbor, the City of Seattle, the City of Snohomish, and the City of Lakewood, under the code editions named on each document. Values change when codes are adopted; always confirm for the address.

    3. USDA Plant Hardiness Zone Map, 2023

      Zones by ZIP code from the USDA Agricultural Research Service. Zone 8a covers average extreme minimum temperatures of 10 to 15°F, 8b covers 15 to 20°F, and 9a covers 20 to 25°F. planthardiness.ars.usda.gov

    4. Office of the Washington State Climatologist

      Monthly climate summaries for March 2021 (the February 2021 Fraser outflow event) and December 2021 (the November 2021 atmospheric rivers and flooding). climate.washington.edu

    5. National Weather Service Seattle and NOAA

      The Puget Sound Convergence Zone explainer from NWS Seattle and NOAA's explainer on atmospheric rivers. weather.gov/zse

    6. U.S. Geological Survey

      Scientific Investigations Report 2007-5159 on Skagit River flood peaks, Professional Paper 1424-C on Puget Sound aquifer systems and surface deposits, and Scientific Investigations Map 3328 on glacial till and outwash. pubs.usgs.gov

    Normals are not forecasts

    A climate normal is a 30-year average. Any given winter can be much wetter, colder, or windier than the normal, and the storms that damage gates are by definition the unusual ones. We use normals to compare places and to plan, and we design for the bad years, not the average one.

    A station is a point

    Each number comes from one instrument at one spot. The two Everett stations differ by more than 20 frost nights a year. Elevation, slope, shade, and distance from water can move a property well away from its nearest station.

    Codes change

    Frost depths and design wind speeds come from the code editions named on each document. When the state adopts new codes, local values can change. The building department for the address is the final word, and we confirm it for every permitted project.

    FAQ

    Climate and gate questions

    How much rain does Northwest Washington get?

    It depends heavily on where you are. NOAA's 1991 to 2020 normals range from 18.47 inches a year at Friday Harbor Airport and 21.74 inches at Coupeville to 48.53 inches at Sedro-Woolley and 71.24 inches at Concrete. Bellingham International Airport averages 34.71 inches and Seattle-Tacoma International Airport 39.34 inches.

    What is the frost depth for a gate post in Washington?

    Local building departments publish their own figure. San Juan County, Island County, the City of Seattle, and the City of Lakewood list 12 inches, and the City of Snohomish lists 18 inches. Gate post footings are designed for leverage and soil as well as frost, so they often go deeper than the code frost depth.

    Which month is wettest for a gate installation?

    November is the wettest month at all 12 stations in this atlas, and roughly two-thirds to three-quarters of each station's annual precipitation falls from October through March. Late spring through early fall is usually the easiest window for trenching and footings, though work continues year-round with the right precautions.

    How often does it freeze in Northwest Washington?

    On average, the low reaches 32°F or colder on about 25 nights a year at Seattle-Tacoma International Airport and about 59 nights a year at Bellingham International Airport, with most other stations in between. Frost is common even where snow is rare.

    What design wind speed applies to a gate on the islands?

    San Juan County and Island County list 110 mph in their 2018 code design criteria, and the City of Oak Harbor lists a 115 mph ultimate wind speed. Those are building design values; a gate is engineered for its own panel area and exposure, and the current value should be confirmed with the building department.

    What are Fraser River outflow winds?

    They are winter winds that carry cold air out of the Fraser River Valley in British Columbia into Whatcom County. In a February 2021 event described by the Washington State Climatologist, outflow produced gusts up to 71 mph on the Lummi Reservation and dropped Bellingham to 21°F.

    Does an atmospheric river affect an automatic gate?

    It can. Several days of heavy rain test every seal and drain at once, flood low driveways, and often come with power outages. Raised operator pads, sealed underground connections, good drainage, and battery backup are the main defenses.

    What USDA hardiness zone is Skagit County?

    The 2023 USDA map places Mount Vernon and Sedro-Woolley in zone 8b and Concrete, farther up the valley, in zone 8a. Zone 8b reflects average extreme winter lows of 15 to 20°F, and 8a of 10 to 15°F.

    Is a solid privacy gate a problem in wind?

    A solid panel catches the full force of the wind, which loads the hinges, posts, and operator far more than an open design. On exposed sites, solid gates need stronger posts and hardware and an operator rated for the panel; semi-open designs reduce the load.

    Why does soil type matter for a gate?

    Glacial till, common across the Puget Lowland, is dense and drains poorly, while outwash is loose, permeable sand and gravel, and river-bottom soils can be soft and wet. Each changes how wide and deep a post footing must be and how water is drained away from it.

    When is the best time of year to install a gate in Western Washington?

    Site work such as trenching and footings is easiest from late spring through early fall, when monthly rainfall is lowest; July or August is the driest month at every station in this atlas. Design and fabrication can happen in winter, so a gate is ready to install as soon as the ground firms up.

    Where is the wettest place in Emerald Gate Systems' service area?

    Among the 12 NOAA stations in this atlas, Concrete in the upper Skagit Valley is the wettest, averaging 71.24 inches of precipitation and 16.3 inches of snow a year under the 1991 to 2020 normals. Friday Harbor Airport is the driest at 18.47 inches.

    Does Whidbey Island need a different gate than the mainland?

    Often, yes. Coupeville averages only 21.74 inches of precipitation, but Island County lists a 110 mph design wind speed and Oak Harbor a 115 mph ultimate wind speed, and salt air reaches waterfront lots. Wind loading, corrosion protection, and ferry logistics usually matter more there than rain.

    Are climate normals the same as the weather I will get?

    No. Normals are 30-year averages that are useful for comparing places and planning, but individual years vary widely, and damaging storms are the unusual events. A gate should be designed for the harsh years at its site, not for the average.

    Ready for a gate built for your climate?

    Tell us where the property is. We will look at exposure, drainage, ground, and power on site and give you a written quote.